Ratnaveer Precision Engineering Limited announces a new order win
TL;DR
With the update on the CCL project in the Q2 FY27 results, what is the total capital expenditure incurred to date against the original project budget, and what is the revised timeline for the commencement of commercial production?
- Capital expenditure: The CCL project’s original total investment budget is approximately ₹338 Cr [1]. However, the Q2 FY27 update does not separately report how much of this budget had been incurred to date; the company-wide FY26 capex figure of ₹114.47 Cr should not be attributed to the CCL project without project-level disclosure.
- Commercial production timeline: The revised operating schedule is for SKU-level trial runs during December 2026–January 2027, followed by commercial production in January–February 2027 [2]. The broader project update identifies February 2027 as the expected commencement month [1].
Thus, the confirmed comparison is ₹338 Cr total project budget versus an unconfirmed CCL-specific spend-to-date figure, with commercial production now targeted for January–February 2027.
How did the Q2 FY27 EBITDA margins reconcile with the company's historical average, and to what extent was the performance driven by the current product mix versus raw material price fluctuations?
Q2 FY27 EBITDA margin was below the recent reported average, and the margin pattern points to gross-margin pressure rather than operating leverage. However, the split between product mix and raw-material prices cannot be quantified from the reported disclosures.
- Margin versus recent average: EBITDA margin was 10.9% in Q2 FY27 [3], versus 11.4% in Q1 FY27 [4] and 14.3% in Q4 FY26 [5]. The simple average of these three reported quarters is 12.2%, making Q2 FY27 1.3 percentage points below that average. This is a recent three-quarter average, not a long-run historical average.
- Why margins fell: Revenue grew 23.1% QoQ, while EBITDA grew only 17.1% QoQ [6] [7]. Gross margin also declined from 16.3% in Q1 FY27 to 14.8% in Q2 FY27 [8] [9]. That combination indicates that incremental revenue converted into EBITDA at a lower rate.
- Product mix versus raw materials: The reported figures are consistent with pressure at the gross-profit level, but the contribution from current product mix versus raw-material price fluctuations could not be confirmed for Q2 FY27. No quantified product-wise mix bridge or raw-material-cost bridge is provided in the cited material.
- Analyst read: Product mix may have been a contributor, but it should not be treated as the established cause. Similarly, the lower gross margin is compatible with raw-material inflation or weaker pass-through, but the evidence does not isolate that effect. The defensible conclusion is therefore margin dilution with an unquantified mix/input-cost split, rather than a demonstrated raw-material-driven or mix-driven outcome.
The company’s Q2 update reports strong revenue and EBITDA growth, but it does not provide the operating bridge needed to attribute that growth or margin movement between product mix and input prices [1].
How does the incremental capacity from the CCL project compare to the company's existing installed capacity, and what specific product grades or market segments is this expansion intended to target to differentiate from existing stainless steel finishing peers?
CCL is a significant diversification, but its physical capacity cannot be expressed as a clean multiple of Ratnaveer’s existing stainless-steel capacity. The CCL facility is planned for 79.2 lakh sheets per year across five lines; the existing stainless-steel business is measured across different product and likely tonnage categories, and a comparable aggregate installed-capacity figure was not reported in the cited material. [10]
An earlier annual-report excerpt cited 1.6 million sheets per year as projected CCL capacity, but that also refers to the CCL facility—not to Ratnaveer’s installed stainless-steel capacity—so it should not be used as the denominator for a “CCL versus existing capacity” calculation. [11] The project is therefore best viewed as a new business platform, rather than simply an expansion of the stainless-steel finishing footprint. Ratnaveer has said its finishing-line business is running near capacity, with separate Phase 2 investment directed toward fasteners, tubes and pipes, sheet-metal components and clips. [12]
What the CCL expansion is targeting
- Product: FR-4 copper-clad laminates for the PCB manufacturing value chain. [11]
- Grades: CCL grades ranging from 140 Tg to 180 Tg, indicating a focus beyond a single standard product specification. [13]
- Customers and geography: Indian PCB manufacturers, with enquiries from customers in Japan, the United States and Europe. [13]
- Demand visibility: Long-term supply agreements and orders already cover nearly 50% of planned CCL capacity, with further customer discussions under way. [10]
- Timing: Trial runs were scheduled for December 2026–January 2027, followed by commercial production targeted for January–February 2027. [2]
The strategic differentiation is thus from a product and end-market shift: Ratnaveer is moving from stainless-steel washers, fasteners, finishing sheets, tubes, pipes and related components into electronic materials supplied to PCB manufacturers. [2] At full utilisation, management has targeted approximately ₹750 Cr of annual CCL revenue and ₹150 Cr of EBITDA, although it cautioned that higher recent CCL prices could require revised guidance. [1]
Key limitation: the cited material does not establish comparable CCL capacities, Tg-grade portfolios or competitive positioning for JTL Industries, Welspun Specialty Solutions, Venus Pipes, Kalyani Steels or Vardhman Special Steels. Accordingly, the differentiation is a clear intended positioning for Ratnaveer, but not yet a demonstrated peer advantage.
Sources
- [1]Ratnaveer Precision Engineering Updates CCL Project Progress and Reports Strong Q2 FY27 Financial Performance — 2026-11-21T14:33:49, p.3
- [2]Ratnaveer Precision Engineering Updates CCL Project Progress and Reports Strong Q2 FY27 Financial Performance — 2026-11-21T14:33:49, p.4
- [3]EBITDA Margin
- [4]EBITDA Margin
- [5]EBITDA Margin
- [6]Revenue INR QoQ
- [7]EBITDA QoQ
- [8]Gross Margin
- [9]Gross Margin
- [10]Ratnaveer Precision Engineering Updates CCL Project Progress and Reports Strong Q2 FY27 Financial Performance — 2026-11-21T14:33:49, p.2
- [11]03 September, 2026 To To National Stock Exchange of India Limited, Exchange BSE Limited Plaza, Plot No. C/1, G Block, — BSE India, 2026-09-03T00:00:00
- [12]04 November, 2026 To To National Stock Exchange of India Limited, BSE Limited Exchange Plaza, Plot No. C/1, G Block, — D162Horukp7Uyq, 2026-11-04T00:00:00
- [13]Ratnaveer Precision Engineering Q2 FY27 Results — Concall Summary — Guidance, 2026-11-04T00:00:00
Keep digging